For 08-14 Dodge Avenger Front Lower Control Arm Tie Rod End Ball Joints Sway Bar

$111.99 Buy It Now or Best Offer
free,30-Day Returns

Seller Store
() %,

Location: Ontario, California, United States
Ships to: US,
Item: 256357784215

eBay 1.Fit For 2007-2010 Chrysler Sebring 2008-2014 Dodge Avenger 2.Package Includes: 2x Outer Tie Rod End -ES800408 2x Front Sway Bar End Link -K80258 2x Front Lower Ball Joint -K500120 1x Front Lower Control Arm-Driver Side -K641333 1x Front Lower Control Arm- Passenger Side -K641334 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. For 08-14 Dodge Avenger Front Lower Control Arm Tie Rod End Ball Joints Sway Bar 1.Fit For 2007-2010 Chrysler Sebring 2008-2014 Dodge Avenger 2.Package Includes: 2x Outer Tie Rod End -ES800408 2x Front Sway Bar End Link -K80258 2x Front Lower Ball Joint -K500120 1x Front Lower Control Arm-Driver Side -K641333 1x Front Lower Control Arm- Passenger Side -K641334 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Control Arm Bushing Replacement Reference: Control arms themselves do not generally wear out, but the control arm bushings and ball joints do, so you will likely need to remove them to service those components. Yet, some OEMs or parts suppliers do not sell bushings and ball joints separately, so you may have to purchase the entire control arm and replace it as a unit. Also, control arms can become bent or damaged as the result of a collision or driving through a deep pothole, so control arms do need to be inspected for damage. Many control arms are now made from forged or sintered aluminum, so you may need to measure for damage or check it on an alignment machine. Picture(A) 1.Remove the coil spring and steering knuckle by following the steps in previous skill drills. 2.Loosen the bolts holding the upper control arm in place. Note that there might be shim packs held in by the bolts. If so, tape them together in their packs, and label their positions. Picture(B) 3.Remove the lower control arm by removing the bolts holding it in place. As you dismantle the system components, carry out a constant inspection of the parts being removed. Doing so will aid you when you need to order replacement parts. You should also mark mating parts with white paint to aid in reassembly. Picture(C) 4.Inspect the upper and lower control arm for wear or damage. If the control arm bushings show signs of excessive wear or deterioration of the bushing material, they will have to be replaced. 5.Replace the worn bushings in the upper and/or lower control arm. Replacement of control arm bushings can be performed two ways — with a hydraulic press with correctly sized press tools or with an air chisel. Be careful using an air chisel: Damage to the control arm can result, such as gouging the mounting surface of the bushing if you slip with the chisel. Picture(D) 6.Press method: Place the control arm in a hydraulic press supported so the bushing is level to the press head. Using the correct-sized adapter, press the bushing out. Picture(E) 7.Using the press, install the new bushing into the control arm. Be careful to start the bushing in straight, or you could bend the control arm. Press it in until the flange bottoms out. Picture(F) 8.Air chisel method: Install the control arm in a vise. Use an air chisel to work the bushing out. Be careful not to gouge the mating surface of the control arm. Picture(G) 9.Using the air hammer, drive the new bushing into place, making sure it is fully seated. Tie Rod End Removing Guideline: Tie rods make the final connection between the steering linkage and the steering arms. The point of connection with the steering linkage is considered the inner tie-rod end, and the end that connects to the steering arm is considered the outer tie-rod end. Checking tie rods is important in identifying steering problems because the ends are frequently damaged or worn. There are two basic types of tie-rod ends: spring loaded and preloaded. Each type has its own procedure for inspection and replacement of the ends. Replacement of tie-rod ends requires an alignment to be performed, or rapid tire wear will occur. Picture(A) 1.Safely raise the vehicle on a lift. 2.Inspect the rubber bellows for any signs of leaks, tears, or damage. 3.With the vehicle raised, have an assistant turn the steering wheel to one side or the other and rock the steering wheel from side to side. 4.On the side farthest out, squeeze the bellows until you make contact with the inner ball joint, and feel for any play in the inner tie-rod joint. 5.Repeat this procedure for the other side. 6.If play is found, replacement of the inner tie-rod ends will be necessary. Picture(B) 7.Remove the front wheel for the side being replaced, and loosen the locknut on the tie-rod end. Picture(C) 8.Remove the cotter pin and nut holding the outer tie-rod end to the steering arm, and separate the tie-rod end from the knuckle, using a tie-rod removal tool, the double hammer method, or a pickle fork. Picture(D) 9.Count the number of turns to remove the outer tie-rod end from the threaded sleeve. Picture(E) 10.Remove the spring clamp from the bellows boot end to the inner tie-rod shaft, and remove the crimp clamp from the bellows boot to the rack-and-pinion housing. A new crimp clamp will have to be used on replacement of the boot. Picture(F) 11.Remove the bellows boot. 12.Using an inner tie-rod tool and the specified wrench to hold the rack, loosen the inner tie rod from the rack, and remove the inner tie-rod end. Picture(G) 13.Install the new inner tie rod in reverse order of removal, and verify that the play is gone. 14.Perform alignment to reset toe after replacement is performed. 15.Test drive to verify repair. Ball Joint Preventive Maintenance: Some ball joints use zerk grease fittings, which allow for periodic lubrication of the moving ball and stationary socket inside the ball joint. Grease fittings can sometimes be found on other suspension components and need to be lubricated as part of a preventive maintenance program provided by the OEM. Loaded Upper Ball Joint Play Measurement: The most common problem in the suspension system is play, or looseness of the parts. Although many of the parts are designed with special connections that allow for movement to accommodate movement of the wheels, excessive play is actually a bad thing. Excessive play magnifies the feel of road imperfections and makes the steering less responsive to steering wheel input. Excessive play is potentially very damaging, as it causes wear on the connecting parts and tires. Naturally, any amount of play in a fixed part is problematic and is frequently a result of part failure. Remember, unwanted looseness in the suspension system can be extremely dangerous and should be corrected as soon as possible. Picture(A) 1.Obtain a properly sized block of wood to fit between the upper control arm and the frame. 2.Place the block of wood between the upper control arm and frame so that it is secure. Picture(B) 3.Raise the vehicle by lifting the body, using the specified lift points, so that the tire is a few inches off the ground. Support the body with a jack stand. 4.Place a dial indicator on the upper control arm and vertically against the steering knuckle. 5.Place a pry bar under the tire, and pry it upward, watching the dial indicator reading as you pry and release. Record the total amount of movement in the joint, and compare to the OEM specifications. Picture(C) 6.Rock the bottom of the tire in and out, watching for play in the lower ball joint, and compare to OEM specifications. Loaded Lower Ball Joint Play Measurement: 1.Jack up the vehicle, place safety stands under the control arms, and look up the exact procedure in the online service information. 2.Place a dial indicator on the lower control arm and vertically against the steering knuckle. 3.Place a pry bar under the tire and pry it upward, watching the dial indicator reading as you pry and release. Record the total amount of movement in the joint, and compare to the OEM specifications. 4.Rock the top of the tire in and out, watching for any play in the upper ball joint specifications. Sway Bar Stabilizer Link Removing Guideline: The sway bar stabilizer components help prevent body roll when cornering. Although the stabilizer bar itself rarely gives any trouble, the rubber bushings on the bar and links wear out. This usually results in increased body roll as well as a clunking noise in the suspension. The stabilizer components should be checked whenever a vehicle is brought into the shop because of handling concerns or suspension-related noises. Picture(A) 1.Safely raise the vehicle on a hoist, or use a jack and place safety stands under the frame. 2.Remove the nut holding the stabilizer bar link. Picture(B) 3.Remove the link by hand. Picture(C) 4.Visually inspect the rubber link grommets for cracks, softness, brittleness, or wear. Repeat with the other link. Frequently Asked Questions (1).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (2).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (3).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (4).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (5).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (6).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. (7).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (8).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (9).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (10).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. Item Specifics Brand : VAP-autoparts Manufacturer Part Number : VAP84371601L Interchange Part Number : K641333,K641334,ES800408,K500120,K80258 OE/OEM Part Number : replacing control arm,suspension arm Superseded Part Number : car tie rod replacement,rods ends Kit or Single Part : Kit Kit Parts Included : Control Arm, Tie Rod End,Ball Joints Manufacturer Warranty : 10 Year Placement on Vehicle : Front Greasable or Sealed : Greasable Universal Fitment : No Quantity : 8Pcs Adjustable : Yes Modified Item : Yes Kit or Single Part : Kit Greasable or Sealed : Greasable Type : Control Arm Kit Items Included : Mounting Hardware Custom Bundle : Yes Surface Finish : Standard Modified Item : No Cotter Pin Hole : Yes Material : Alloy Steel Shipping WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to all the auto parts purchased from VAP-AUTOPARTS. (2).VAP-AUTOPARTS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).VAP-AUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise VAP-AUTOPARTS has the right to refuse any replacement requests. (5).VAP-AUTOPARTS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise VAP-AUTOPARTS has the right to refuse any replacement requests. (6).VAP-AUTOPARTS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).VAP-AUTOPARTS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales For Ford Ranger 2.3L 2.5L F150 Expedition Lincoln Mercury FD487 Ignition Coil USD 30.99 Front Driver For 2010-2015 Chevrolet Chevy Cruze w/ Motor Power Window Regulator USD 39.49 6x Ignition Coils for Nissan Frontier Pathfinder Altima Maxima 3.5L 4.0L UF349 USD 46.99 4x Ignition Coil For 00-08 Toyota Corolla Celica Matrix 1.8L UF247 90919-02339 USD 35.99 For Chevrolet Silverado GMC Sierra 1500 4.8L 5.3L 2006-2000 Square Ignition Coil USD 66.99 Newly Listed Fits 2006-2007 Chevrolet Monte Carlo 2006-2013 Impala Front Headlights Pair USD 110.99 Driver Power LH Side View Mirror For 94-97 Chevrolet S10 95-97 Blazer Truck SUV USD 25.09 2pcs Upstream Downstream Air Fuel Ratio Oxygen Sensor For 06-09 Mazda 3 2.0L USD 39.99 Fits Honda FIT 2014-2020 Headlights Assembly Pair Replacement USD 296.99 Oxygen O2 Sensor for 1996-2001 Acura Integra 1.8L Upstream and Downstream 2pcs USD 24.99 Terms & Contact Shipping Policy Payment Policy Return Policy FAQ About Us For 08-14 Dodge Avenger Front Lower Control Arm Tie Rod End Ball Joints Sway Bar 1.Fit For 2007-2010 Chrysler Sebring 2008-2014 Dodge Avenger 2.Package Includes: 2x Outer Tie Rod End -ES800408 2x Front Sway Bar End Link -K80258 2x Front Lower Ball Joint -K500120 1x Front Lower Control Arm-Driver Side -K641333 1x Front Lower Control Arm- Passenger Side -K641334 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Control Arm Bushing Replacement Reference: Control arms themselves do not generally wear out, but the control arm bushings and ball joints do, so you will likely need to remove them to service those components. Yet, some OEMs or parts suppliers do not sell bushings and ball joints separately, so you may have to purchase the entire control arm and replace it as a unit. Also, control arms can become bent or damaged as the result of a collision or driving through a deep pothole, so control arms do need to be inspected for damage. Many control arms are now made from forged or sintered aluminum, so you may need to measure for damage or check it on an alignment machine. Picture(A) 1.Remove the coil spring and steering knuckle by following the steps in previous skill drills. 2.Loosen the bolts holding the upper control arm in place. Note that there might be shim packs held in by the bolts. If so, tape them together in their packs, and label their positions. Picture(B) 3.Remove the lower control arm by removing the bolts holding it in place. As you dismantle the system components, carry out a constant inspection of the parts being removed. Doing so will aid you when you need to order replacement parts. You should also mark mating parts with white paint to aid in reassembly. Picture(C) 4.Inspect the upper and lower control arm for wear or damage. If the control arm bushings show signs of excessive wear or deterioration of the bushing material, they will have to be replaced. 5.Replace the worn bushings in the upper and/or lower control arm. Replacement of control arm bushings can be performed two ways — with a hydraulic press with correctly sized press tools or with an air chisel. Be careful using an air chisel: Damage to the control arm can result, such as gouging the mounting surface of the bushing if you slip with the chisel. Picture(D) 6.Press method: Place the control arm in a hydraulic press supported so the bushing is level to the press head. Using the correct-sized adapter, press the bushing out. Picture(E) 7.Using the press, install the new bushing into the control arm. Be careful to start the bushing in straight, or you could bend the control arm. Press it in until the flange bottoms out. Picture(F) 8.Air chisel method: Install the control arm in a vise. Use an air chisel to work the bushing out. Be careful not to gouge the mating surface of the control arm. Picture(G) 9.Using the air hammer, drive the new bushing into place, making sure it is fully seated. Tie Rod End Removing Guideline: Tie rods make the final connection between the steering linkage and the steering arms. The point of connection with the steering linkage is considered the inner tie-rod end, and the end that connects to the steering arm is considered the outer tie-rod end. Checking tie rods is important in identifying steering problems because the ends are frequently damaged or worn. There are two basic types of tie-rod ends: spring loaded and preloaded. Each type has its own procedure for inspection and replacement of the ends. Replacement of tie-rod ends requires an alignment to be performed, or rapid tire wear will occur. Picture(A) 1.Safely raise the vehicle on a lift. 2.Inspect the rubber bellows for any signs of leaks, tears, or damage. 3.With the vehicle raised, have an assistant turn the steering wheel to one side or the other and rock the steering wheel from side to side. 4.On the side farthest out, squeeze the bellows until you make contact with the inner ball joint, and feel for any play in the inner tie-rod joint. 5.Repeat this procedure for the other side. 6.If play is found, replacement of the inner tie-rod ends will be necessary. Picture(B) 7.Remove the front wheel for the side being replaced, and loosen the locknut on the tie-rod end. Picture(C) 8.Remove the cotter pin and nut holding the outer tie-rod end to the steering arm, and separate the tie-rod end from the knuckle, using a tie-rod removal tool, the double hammer method, or a pickle fork. Picture(D) 9.Count the number of turns to remove the outer tie-rod end from the threaded sleeve. Picture(E) 10.Remove the spring clamp from the bellows boot end to the inner tie-rod shaft, and remove the crimp clamp from the bellows boot to the rack-and-pinion housing. A new crimp clamp will have to be used on replacement of the boot. Picture(F) 11.Remove the bellows boot. 12.Using an inner tie-rod tool and the specified wrench to hold the rack, loosen the inner tie rod from the rack, and remove the inner tie-rod end. Picture(G) 13.Install the new inner tie rod in reverse order of removal, and verify that the play is gone. 14.Perform alignment to reset toe after replacement is performed. 15.Test drive to verify repair. Ball Joint Preventive Maintenance: Some ball joints use zerk grease fittings, which allow for periodic lubrication of the moving ball and stationary socket inside the ball joint. Grease fittings can sometimes be found on other suspension components and need to be lubricated as part of a preventive maintenance program provided by the OEM. Loaded Upper Ball Joint Play Measurement: The most common problem in the suspension system is play, or looseness of the parts. Although many of the parts are designed with special connections that allow for movement to accommodate movement of the wheels, excessive play is actually a bad thing. Excessive play magnifies the feel of road imperfections and makes the steering less responsive to steering wheel input. Excessive play is potentially very damaging, as it causes wear on the connecting parts and tires. Naturally, any amount of play in a fixed part is problematic and is frequently a result of part failure. Remember, unwanted looseness in the suspension system can be extremely dangerous and should be corrected as soon as possible. Picture(A) 1.Obtain a properly sized block of wood to fit between the upper control arm and the frame. 2.Place the block of wood between the upper control arm and frame so that it is secure. Picture(B) 3.Raise the vehicle by lifting the body, using the specified lift points, so that the tire is a few inches off the ground. Support the body with a jack stand. 4.Place a dial indicator on the upper control arm and vertically against the steering knuckle. 5.Place a pry bar under the tire, and pry it upward, watching the dial indicator reading as you pry and release. Record the total amount of movement in the joint, and compare to the OEM specifications. Picture(C) 6.Rock the bottom of the tire in and out, watching for play in the lower ball joint, and compare to OEM specifications. Loaded Lower Ball Joint Play Measurement: 1.Jack up the vehicle, place safety stands under the control arms, and look up the exact procedure in the online service information. 2.Place a dial indicator on the lower control arm and vertically against the steering knuckle. 3.Place a pry bar under the tire and pry it upward, watching the dial indicator reading as you pry and release. Record the total amount of movement in the joint, and compare to the OEM specifications. 4.Rock the top of the tire in and out, watching for any play in the upper ball joint specifications. Sway Bar Stabilizer Link Removing Guideline: The sway bar stabilizer components help prevent body roll when cornering. Although the stabilizer bar itself rarely gives any trouble, the rubber bushings on the bar and links wear out. This usually results in increased body roll as well as a clunking noise in the suspension. The stabilizer components should be checked whenever a vehicle is brought into the shop because of handling concerns or suspension-related noises. Picture(A) 1.Safely raise the vehicle on a hoist, or use a jack and place safety stands under the frame. 2.Remove the nut holding the stabilizer bar link. Picture(B) 3.Remove the link by hand. Picture(C) 4.Visually inspect the rubber link grommets for cracks, softness, brittleness, or wear. Repeat with the other link. Frequently Asked Questions (1).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (2).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (3).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (4).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (5).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (6).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. (7).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (8).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (9).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (10).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. Item Specifics Brand : VAP-autoparts Manufacturer Part Number : VAP84371601L Interchange Part Number : K641333,K641334,ES800408,K500120,K80258 OE/OEM Part Number : replacing control arm,suspension arm Superseded Part Number : car tie rod replacement,rods ends Kit or Single Part : Kit Kit Parts Included : Control Arm, Tie Rod End,Ball Joints Manufacturer Warranty : 10 Year Placement on Vehicle : Front Greasable or Sealed : Greasable Universal Fitment : No Quantity : 8Pcs Adjustable : Yes Modified Item : Yes Kit or Single Part : Kit Greasable or Sealed : Greasable Type : Control Arm Kit Items Included : Mounting Hardware Custom Bundle : Yes Surface Finish : Standard Modified Item : No Cotter Pin Hole : Yes Material : Alloy Steel ShippingWarrantyReturnDiscountSales Tax WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to all the auto parts purchased from VAP-AUTOPARTS. (2).VAP-AUTOPARTS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).VAP-AUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise VAP-AUTOPARTS has the right to refuse any replacement requests. (5).VAP-AUTOPARTS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise VAP-AUTOPARTS has the right to refuse any replacement requests. (6).VAP-AUTOPARTS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).VAP-AUTOPARTS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of vap-autoparts. All rights reserved.

Frequently Asked Questions About For 08-14 Dodge Avenger Front Lower Control Arm Tie Rod End Ball Joints Sway Bar in My Website

clinic-key.com is the best online shopping platform where you can buy For 08-14 Dodge Avenger Front Lower Control Arm Tie Rod End Ball Joints Sway Bar from renowned brand(s). clinic-key.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling For 08-14 Dodge Avenger Front Lower Control Arm Tie Rod End Ball Joints Sway Bar on clinic-key.com?

clinic-key.com helps you to shop online and delivers Madness to your doorstep. The best-selling Madness on clinic-key.com are: It’s A Mad Mad Mad Mad World Movie Soundtrack LP 1963 First Pressing MAD Xtreme APC All Purpose Degreaser Car Exterior Components & Upholstery 1 GAL Ne-Yo When You’re Mad / So Sick Ft. LL Cool J Remixes Vinyl 12″ Single 2006 NEW UPS Shipping OMRON CJ1W-MAD42 CJ1WMAD42 PLC Analog Module 2024 UD Marvel Beginnings Vol 2 Series 2 Flipped FX Foil -YOU PICK FINSIH UR SET /300 Animals As Leaders – The Madness Of Many 2LP [Bone w/B&W Marble] *SEALED* Nintendo Game Boy Authentic *Pick Your Game* Cart Only Cleaned & Tested MAD Magazine Treasure Trove Of Trash 2024 Barnes & Noble Edition 2024 New Berserker (gray coat) – Waterdeep Dungeon of the Mad Mage #17 D&D Barbarian Mini Madness the rise & fall vinyl 12″ album gatefold cover 2021 new and sealed 1957 Mad Magazine #31 NEW Metal Sign: Mount Rushmore Theme HEXILES #3 (OF 6) (MR) (PRESALE 1/15/25) MADNESS Baggy Trousers 1980 UK 7″ vinyl single original stiff records Suggs Joan Sutherland – Mad Scenes (Hamlet, I Puritani, Dinorah)[NH09-061] original LP Madchild – The Darkest Hour Picture Disc Vinyl 12” Record Swollen Members LP Linda Ronstadt Mad Love CD – RARE – Very Good Condition [Japan Used Record] Mad – Eyeball 7 Inch Kbd Punk Heaven Us Marihuana Movie Poster 2″ X 3″ Fridge Magnet. Marijuana Reefer Madness Lucky Craft FATCBBDMAJIC2.2/Floating Pick One! JAPAN MADE Madness – 7 (2021 Reissue) *NEW Sealed Vinyl Record LP* Madness – Our House / Cardiac Arrest – 80’s Rock 45 w/PS EX VINYL Record (Ska) Devil in the White City : Murder, Magic, and Madness at the Fair That Changed… The Wisdom of Crowds: Book Three (The Age of Madness) – Hardcover – ACCEPTABLE Classic & Musical TCM DVD Movies Pick and Choose 1980’s – Flat Rate Shipping Queen – I’m Going Slightly Mad – 12″ UK Vinyl 1991 Single Gatefold Sleeve 6 x MADNESS – 7” Singles Bundle plus poster [SOUL/JAZZ]~EXC LP~JOHN KLEMMER~Magnificent Madness~{Original 1980~ELEKTRA~Issue Human Paladin of the Oath of Vengeance – Waterdeep Dungeon Mad Mage #23 D&D Mini Madness ~ GHS-4003 1983 Lp 1st Press (Near Mint) Madness The Rise and Fall RARE Vintage Vinyl 1982 Made in W. Germany!!! Agent Steel Mad Locust Rising EP 1986 Combat Records Blue Vinyl Madness Elvis Costello Tomorrow’s Just Another vinyl LP 12″ 1983 Stiff Records The 78-Story Treehouse: Moo-vie Madness! (The Treehouse Books) – GOOD Madness – It Must Be Love, Calling Cards 45 rpm 7″ Single Geffen Records VG+ The Mad Lads – A New Beginning on Volt Nadine sutherland 12″ action lp terror fabulous vinyl record reggae version Madness – Yesterdays Men 7 inch vinyl single MADNESS SELF TITLED 12″ SKA JAZZ RECORD ALBUM VINYL LP GEFFEN GHS-4003 1983 KGP – Necrology CD 2005 horrorcore killmusick bedlam rap wicked madness American Jet Set Marauder Mini MAD-3R MWO Mech Miniature Compatible with Battletech Tales Of Madness And Horror by Gerard McHugh (CD, Promo) LE SSERAFIM CRAZY 4th Mini Album CD+Photo Book+2 Card+3 Sticker+Poster+Toy+GIFT Madness in Miniature 5 SARDONYX AGATES MAD MONGORO RIVER MADAGASCAR CRAZY LACE PALM STONE #159 Child of a Mad God: A Tale of the Coven – Hardcover By Salvatore, R. A. – GOOD ALL LP’S/VINYL ARE JUST $4.00-$10.00 EACH!!~ROCK/CLASSIC ROCK &MORE~LISTING #2 Bernie Green vg stoc / vg+ mono LP Musically Mad John Lee Hooker –  Mad Man Blues – CHESS CH292507 LP Record -EXCELLENT/EXCELLENT Mad Mike & The Maniacs Quarter To Four The Hunch Hunch Records 45 RPM R3846 Bette Midler~Divine Madness Soundtrack SD 16022 SEALED LP Joe Cocker – Mad Dogs & English Men 2LP ~ Mint Sealed Original Promo A&M GPK 2022 Bookworms Base Singles, Pick a Card Star Wars Episode III Revenge of the Sith 2005 Trading Cards, Foil, Stickers… A Certain Amount of Madness: The Life Politics and Legacies of Thomas Sankara (B Edward Lee Honza Vojtísek Czech Extreme (Paperback) Seal- Crazy / Sparkle – Sire WB 45 Vinyl Record #5830 Madness One Better Day UK Vinyl 7″ LTD Poster Sleeve Stiff Records EX, BUY 201 Danny Elfman ‎Doctor Strange In The Multiverse Of Madness OST Splatter Colored Madness Absolutely Vinyl 12″ Sire Records 1980 Ska EX/EX The Psychopath Test: A Journey Through the Madness Industry – VERY GOOD Iron Maiden – Can I Play With Madness/Black Bart Blues 2014 UK 45rpm SEALED Sons of Survival – DOCTORS OF MADNESS The Psychopath Test: A Journey Through the Madness Industry – VERY GOOD MAD RIVER – Self Titled, 1968 S/T LP, Capitol Records – ST 2985 BIRTHA Can’t Stop The Madness Vinyl LP Record Album 1973 ABC/Dunhill Gatefold Madness – Our House: Very Best Of LP [Vinyl New] Sealed Record Album Sheena Easton – Madness, Money and Music (Limited Edition green Vinyl) (2023) CD wholesale lots YOU PICK’EM!!CHEAP BULK shipping!! HOT #6 NEW COUNTRY TODAY!!! Madness – Our House – 45 Picture Sleeve Only – No Record Madness:Lovestruck/We are love:Uk Virgin:Jukebox:1999 Various Artists : Mad Love CD Chick Corea – The Mad Hatter Vinyl LP – 1978 First Press – Polydor PD-1-6130 MIKE RUSSO SHE LETS ME WATCH HER MOM AND POP FIGHT 1963 SINGLE SIDE 33rpm 5″ MAD Morbid Angel – Altars Of Madness VINYL Alice in the Country of Hearts: The Mad Hatter’s Late Night Tea P – VERY GOOD Mad Anthony – The Stourbridge Lion Rpm 45 Mad River – Orange Fire EP – USA 7″ 45 PS (numbered) – psych acid rock garage Make Your Own CD Lot ~ $1.99 Each ~ $5.24 Shipping Any Order Size ~ Country Rock 1994 Mad Lion: Take It Easy/Big Box of Blunts 12 Vinyl Record – Weeded Records Clutch – Mad Sidewinder / Outland Special Clearance Vinyl Single RSD Ltd /5000 DANCE CRAZE Specials Madness Selecter 2 TONE Original ’81 UK Ska LP w/poster 1994 Fleer Flair Marvel Annual Trading Cards 1-150 * You-Pick* Complete your set The Center Cannot Hold: My Journey Through Madness – Paperback – GOOD MADNESS THE GET UP DVD AND CD SOUNDTRACK BRAND NEW AND SEALED CD # 2023 Topps Chrome Star Wars REFRACTORS & INSERTS pick a card finish your set Joe Cocker”Mad Dogs & Englishmen” Vinyl (EX) Obsession Methods Of Madness Black Vinyl LP Record New For GLOCK 26 27 33 39 GEN 1 2 3 4 5 Stainless Steel Guide Rod Assembly G26 Camel – Moonmadness [New Vinyl LP] UK – Import Madness 45 The Sun and the Rain NEW unplayed Marvel’s Doctor Strange in the Multiverse of Madness – Original Soundtrack 2XL Tom Holkenborg – Furiosa: A Mad Max Saga (Original Soundtrack) [New Vinyl LP] Metal Meat by Mad Butcher (Record, 2022) Mad Dogs & Englishmen by Joe Cocker: Used Mad Men: Season 2 – DVD – GOOD HEXILES #2 (OF 6) (MR) (PRESALE 12/11/2024) Brain on Fire (10th Anniversary Edition): My Month of Madness Jerry & Reggie MAD MIKE ROCKER 45RPM Shoo Shoo / Dream Baby PROMO – MOC 656 -EX+ Kung Fu Vampire Dead Sexy Cd Autographed By Savzilla & Kung Fu Vampire Mens Pullover Fleece Hoodie