$37.8 Buy It Now or Best Offer
free,30-Day Returns
Seller Store fiberoptictoolsshopping
(12) 100.0%,
Location: shanghai, Shanghai
Ships to: US,
Item: 315530353152
Return shipping will be paid by:Seller
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money Back
Unbranded:Unbranded
Fiber Cleaver:Fiber Cleaver
MPN:Does Not Apply
Country/Region of Manufacture:China
Blade::16 Surface Blade
Package Include 2::Protect Bag
Package Include 1::Fiber Cleaver
New Fiber Cleaver Cable Cutting Knife FTTH Fiber Optic Knife Tools Cutter 16 surface blade Description: 1. Please lift up the top lever of optical fiber cover. Open the cover clip of single-core fiber clamp. Confirm that the sliding bar of cutter is at the fort position.2. Put the optical iber into the groove of single-core fiber clamp. Align the coating line with the scale of proper cutting length of optical fier. (For instance, if the cutting length is 18m, align the coating line with the position of 18mm on the scale.) Then check the bare fiber whether it is straight.3. The optical fiber and fiber chips are very tiny and sharp. If it is penetrated into the finger or eye, it will al cause the injury. It thus should be very careful during the operation. For the safe operation, the operator should wear the protective glasses.4. Please throw the fiber chips into the special container that is separated from general garbage.5. the cutter installed on the machine is very sharp. Do not touch i by hands, otherwise it may hurt your hands. 6. Please be noted that if the top levar of optical fiber cover is impacted, it will also cause the failure. The damaged top lever will reduce the performanc of fiber cleaver.7. In case of the failure or abnormal conditions, please stop the operation. Do not disasemble or modify the machine. Please contact the service department of our company as mentioned below. Requirements on the replacement of fiber cleaver using the original cutter. To guarantee the quality and performance of the SKL-6C, the precondition for no need of adjusting the cutting force after the replacement of cutter is to use the original cutter of fiber cleaver. Warning 1: When using the non-optical adjusting cutter for the replacement, i may be unable to replace and install the cutter or adjust the cutting force.SKL-6C adopts the special cutter fixing screw and it’s no need to adjust the height of cutter even turming the cutting edge.Therefore, if using the non-original cutter for the replacement of fiber cleaver, the installation may fail. Besides, the cutting-force adjusting screw(the one in red below) is also matched with the precision of original cutter. If using the replacement cutter of other manufacturers, the height of cutter may not be adjusted. Warning 2: If using the non-original cutter for the replacement of fiber cleaver, it will be unable to quarantee i quality and performance. 1. IntroductionApplicable Diameter of Bar Fiber: 125umApplicable quantity of fiber core: Single core(0.25 & 0.9mm)-12 core ribbon fiber-2.5 covered wireCutting Length for Optical fiber: 18mmDimension: 71.2(w) x 67.2(D) x 52(H) mmWeight: 230g 2. Operations(1). Please lift up the top lever of optical fiber cover. Open the cover clip of single-core fiber clamp. Confirm that the sliding bar o cutter is at the front position.(2). Put the optical fiber into the groove of single-core fiber clamp. Align the coating line with the scale of proper cutting length of optical fiber. (For instance, if the cutting length is 18mm, align the coating line with the position of 18mm on the scale.) Then check the bare fiber whether it is straight.(3). Cover the cover clip of single-core fiber clamp to clamp the fiber.(4). Please close the optical fiber cover and put down the top lever. Push the sliding block of cutter to cut off the optical fiber. Lift up the top lever of optical fiber cover. Open the cover, press the fiber and open the single-core fiber clamp. Take out the fiber and clear the fiber chips. 3. MaintenanceDaily Cleaning To maintain the cutting performance of fiber cleaver, t s essential to perform the daily cleaning. Please clean the cutting edge, the rubber block that clamps the fiber and pillow block using the cotton awab with the anhydrous alcohol. the loading chute of fiber clamp and groove of single-core fiber should also be cleaned. Attention:. In case of anydust on the cutter or fiber clamping block, the cutting performance may be reduced and it may also be impossible to achieve the smooth cutting end face of optical fiber.. When cleaning the machine, do not use th fluid except the alcohol.. If the fiber chips left on the rubber part of fiber clamping block, the cutting performance may be reduced and it may also be impossible the achieve the smooth cutting end face of optical fiber.Adjusting Method of Cutting EdgeAfter many times of cutting, the cutting will be consumed, resulting in the situations of unable cutting off or detective cutting end face. If the situation continues, it will be necessary to adjust the position of cutting edge. Please adjust the direction of cutting edge and adopt the new position of cutter according to the following steps.[Reference] Number of cutting for 1 point of cutting edge; 1000 core wir1: Open the right decorative cover using the cross point screwdriver.2: Please use the slotted screwdriver to loosen the screw fixed on the cutter.3: Turn the cutter to the next new cutting edge. Use the cotton swab to press the side or front of cutter and push it outside. It will then be easy to turn the cutter. Attention. When changing the position of cutting edge(turning the cutter), do not turn the cutter by hands directly.. Do no use the metal tools(such as the tweezers) to turn the cutter. The use of metal tools may damage the cutter.4: Fasten the fixing screw for the cutter[Reference] The proper fastening torque is about 0.98 Nm(10 kg f*cm) Attention. Please be noted that do not over-fasten the fixing screw fot the cutter, otherwise it may damage the screw.5: Try to cut off the fiber 1 or 2 times. Use the screen of fusion splicer to confirm the cutting end face of fiber. If the cutting end face is not favorable, please adjust the height of cutter.(Please refer to adjusting method of height of cutter.)6: Adjust the cutting angle. If the fusion effect is favorable, please lock the right decorative cover. Adjusting Method for Height of Cutter0: SKL-6C, please take down the right decorative cover at first.1: Please loosen 2 fixing screws.2. Please loosen the screw that is used to fix the height of cutter.3: Put the automatic pencil core or wooden thin bar on the fiber clamping block. Move the sliding bar of cutter back and forth and rotate the adjusting screw for the height of cutter at the same time. The highest point of cutter edge that contacts the pencil core or wooden thin bar is treated as the reference point (0um). Key Points. When adjusting the height of cutter upwards, it should loosen the height adjusting screw at first and then rotate it along the clckwise direction.. When adjusting the height of cutter downwards, it should rotate height adjusting screw along the anticlockwise direction at first and then fasten the screw.(Please use the cotton swab to press the cutter downwards and then rotate the height adusting screw ath the same time.)When adjusting the height of cutter downwards, it should use the cotton swab to press the cutter downwards and then rotate the height adjusting screw along the anticlockwise direction at the same time.4. Please rtate the height adjusting screw 1/4-1/2 circle along the clockwise direction from the reference point. Attention. Please be noted that the height of cutter should not be adjusted too high, otherwise it may damage the pillow block and fiber end face.5. Please fasten the fixing screw for the height of [Reference] Proper Fastening Torque: about 0.59N.m(6kgfcm)6. Please fasten 2 fixing screws that are loosened in Step 1. [Reference] Proper Fastening Torque: about 0.98N.m(10kgfcm) Replacement of Cutter0: SKL-6C, please take down the right decorative cover at first.1. Take down the fixing screw of cutter.2. Please use the too such as tweezers to take out the cutter. Please be noticed that the cutter should not touch other parts. Attention: . The cutter is precisely ground if the cutter edge touches the metals, it may be damaged and this be unable to achieve the normal cutting performance. Please be careful during the operation.. When using the metal tweezers, do not damage the cutter edge.. When taking the cutter, please use the gloves, but not the hands to touch it directly.. Please separate the removed cutter from the normal garbage. It should be treated proeperly. 3. When installing the new cutter, please make the marker of “1” upwards. Put the cutter on the fixed plane of cutter fixedplate. Puch it into the groove slightly.At the same time, please align the central hole of cutter with the central position of screw hole at the installation side. 4. Please press the side surface of cutter using the finger. Fasten the fixing screw.[Reference] Proper Fastering Torque: about 0.98N-m(10kgfcm) 5. Please refer to Adjusting Method for Height of Cutter in Page 2 and adjust the height of cutter according to related step. 6. Install the right decorative cover after being adjusted. Poor Cutting(damaged cutting surface)Reasons to cause the poor cutting may include:(A) The optical fiber is not put on the cutter straightly.→Please place the optical fiber straightly.(B) The position of cutter is too high.→Please adjust the height of cutter.(C) There are wastes on the fiber clamping block.→Please clean the fiber clamping block(D) There are foreign materials such as the dust on the cutter.→Please clean the cutter.(E) There are foreign materials such as the dust on the optical fiber.→Please remove the fiber coating and clean the part of bare fiber.→The upper and lowesr presure pad for the optical fiber may be loosened during the transportation.If the poor cutting continues, please contact the department of maintenance surface of our company. Leveling MethodThere may be the clearance of upper and lowest pressure pad during the transportation of SKL-6C.A. Take down the fiber clamp at first and then loosen 3 hex screws on the fast enings;B. Align the upper and lower presure pad and clench it by the left hand(guarantee that there is no clearance of pressure pad and then fasten 3 hex screws);C. Observe the whole machine whether there is any clearance of pressure pad in the sunlight. If no, please continue the cutting. If yes, please repeat steps of A and B. Shipping: Usual We Ship the Item within 1-3 days after the payment is cleared. We Will Ship The Item By E-packing /China Post/ Fedex / EMS / TNT / DHL /UPS All the packing Ship with tracking number. Payment: We Accept Paypal Terms Of Sale: Please Check and Confirm the Part No.before purchase. We do not responsible on the custom tax for any order. Customer should pay for the custom fee in any case. If you want to return the item,pls contact us first and make sure the item is un-opened. Accepted 30 days Ebay return policy.
Frequently Asked Questions About Fiber Cleaver Cable Cutting Knife FTTH Fiber Optic Knife Tools Cutter 16 Surface in My Website
clinic-key.com is the best online shopping platform where you can buy Fiber Cleaver Cable Cutting Knife FTTH Fiber Optic Knife Tools Cutter 16 Surface from renowned brand(s). clinic-key.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling Fiber Cleaver Cable Cutting Knife FTTH Fiber Optic Knife Tools Cutter 16 Surface on clinic-key.com?
clinic-key.com helps you to shop online and delivers Madness to your doorstep. The best-selling Madness on clinic-key.com are: It’s A Mad Mad Mad Mad World Movie Soundtrack LP 1963 First Pressing MAD Xtreme APC All Purpose Degreaser Car Exterior Components & Upholstery 1 GAL Ne-Yo When You’re Mad / So Sick Ft. LL Cool J Remixes Vinyl 12″ Single 2006 NEW UPS Shipping OMRON CJ1W-MAD42 CJ1WMAD42 PLC Analog Module 2024 UD Marvel Beginnings Vol 2 Series 2 Flipped FX Foil -YOU PICK FINSIH UR SET /300 Animals As Leaders – The Madness Of Many 2LP [Bone w/B&W Marble] *SEALED* Nintendo Game Boy Authentic *Pick Your Game* Cart Only Cleaned & Tested MAD Magazine Treasure Trove Of Trash 2024 Barnes & Noble Edition 2024 New Berserker (gray coat) – Waterdeep Dungeon of the Mad Mage #17 D&D Barbarian Mini Madness the rise & fall vinyl 12″ album gatefold cover 2021 new and sealed 1957 Mad Magazine #31 NEW Metal Sign: Mount Rushmore Theme HEXILES #3 (OF 6) (MR) (PRESALE 1/15/25) MADNESS Baggy Trousers 1980 UK 7″ vinyl single original stiff records Suggs Joan Sutherland – Mad Scenes (Hamlet, I Puritani, Dinorah)[NH09-061] original LP Madchild – The Darkest Hour Picture Disc Vinyl 12” Record Swollen Members LP Linda Ronstadt Mad Love CD – RARE – Very Good Condition [Japan Used Record] Mad – Eyeball 7 Inch Kbd Punk Heaven Us Marihuana Movie Poster 2″ X 3″ Fridge Magnet. Marijuana Reefer Madness Lucky Craft FATCBBDMAJIC2.2/Floating Pick One! JAPAN MADE Madness – 7 (2021 Reissue) *NEW Sealed Vinyl Record LP* Madness – Our House / Cardiac Arrest – 80’s Rock 45 w/PS EX VINYL Record (Ska) Devil in the White City : Murder, Magic, and Madness at the Fair That Changed… The Wisdom of Crowds: Book Three (The Age of Madness) – Hardcover – ACCEPTABLE Classic & Musical TCM DVD Movies Pick and Choose 1980’s – Flat Rate Shipping Queen – I’m Going Slightly Mad – 12″ UK Vinyl 1991 Single Gatefold Sleeve 6 x MADNESS – 7” Singles Bundle plus poster [SOUL/JAZZ]~EXC LP~JOHN KLEMMER~Magnificent Madness~{Original 1980~ELEKTRA~Issue Human Paladin of the Oath of Vengeance – Waterdeep Dungeon Mad Mage #23 D&D Mini Madness ~ GHS-4003 1983 Lp 1st Press (Near Mint) Madness The Rise and Fall RARE Vintage Vinyl 1982 Made in W. Germany!!! Agent Steel Mad Locust Rising EP 1986 Combat Records Blue Vinyl Madness Elvis Costello Tomorrow’s Just Another vinyl LP 12″ 1983 Stiff Records The 78-Story Treehouse: Moo-vie Madness! (The Treehouse Books) – GOOD Madness – It Must Be Love, Calling Cards 45 rpm 7″ Single Geffen Records VG+ The Mad Lads – A New Beginning on Volt Nadine sutherland 12″ action lp terror fabulous vinyl record reggae version Madness – Yesterdays Men 7 inch vinyl single MADNESS SELF TITLED 12″ SKA JAZZ RECORD ALBUM VINYL LP GEFFEN GHS-4003 1983 KGP – Necrology CD 2005 horrorcore killmusick bedlam rap wicked madness American Jet Set Marauder Mini MAD-3R MWO Mech Miniature Compatible with Battletech Tales Of Madness And Horror by Gerard McHugh (CD, Promo) LE SSERAFIM CRAZY 4th Mini Album CD+Photo Book+2 Card+3 Sticker+Poster+Toy+GIFT Madness in Miniature 5 SARDONYX AGATES MAD MONGORO RIVER MADAGASCAR CRAZY LACE PALM STONE #159 Child of a Mad God: A Tale of the Coven – Hardcover By Salvatore, R. A. – GOOD ALL LP’S/VINYL ARE JUST $4.00-$10.00 EACH!!~ROCK/CLASSIC ROCK &MORE~LISTING #2 Bernie Green vg stoc / vg+ mono LP Musically Mad John Lee Hooker – Mad Man Blues – CHESS CH292507 LP Record -EXCELLENT/EXCELLENT Mad Mike & The Maniacs Quarter To Four The Hunch Hunch Records 45 RPM R3846 Bette Midler~Divine Madness Soundtrack SD 16022 SEALED LP Joe Cocker – Mad Dogs & English Men 2LP ~ Mint Sealed Original Promo A&M GPK 2022 Bookworms Base Singles, Pick a Card Star Wars Episode III Revenge of the Sith 2005 Trading Cards, Foil, Stickers… A Certain Amount of Madness: The Life Politics and Legacies of Thomas Sankara (B Edward Lee Honza Vojtísek Czech Extreme (Paperback) Seal- Crazy / Sparkle – Sire WB 45 Vinyl Record #5830 Madness One Better Day UK Vinyl 7″ LTD Poster Sleeve Stiff Records EX, BUY 201 Danny Elfman Doctor Strange In The Multiverse Of Madness OST Splatter Colored Madness Absolutely Vinyl 12″ Sire Records 1980 Ska EX/EX The Psychopath Test: A Journey Through the Madness Industry – VERY GOOD Iron Maiden – Can I Play With Madness/Black Bart Blues 2014 UK 45rpm SEALED Sons of Survival – DOCTORS OF MADNESS The Psychopath Test: A Journey Through the Madness Industry – VERY GOOD MAD RIVER – Self Titled, 1968 S/T LP, Capitol Records – ST 2985 BIRTHA Can’t Stop The Madness Vinyl LP Record Album 1973 ABC/Dunhill Gatefold Madness – Our House: Very Best Of LP [Vinyl New] Sealed Record Album Sheena Easton – Madness, Money and Music (Limited Edition green Vinyl) (2023) CD wholesale lots YOU PICK’EM!!CHEAP BULK shipping!! HOT #6 NEW COUNTRY TODAY!!! Madness – Our House – 45 Picture Sleeve Only – No Record Madness:Lovestruck/We are love:Uk Virgin:Jukebox:1999 Various Artists : Mad Love CD Chick Corea – The Mad Hatter Vinyl LP – 1978 First Press – Polydor PD-1-6130 MIKE RUSSO SHE LETS ME WATCH HER MOM AND POP FIGHT 1963 SINGLE SIDE 33rpm 5″ MAD Morbid Angel – Altars Of Madness VINYL Alice in the Country of Hearts: The Mad Hatter’s Late Night Tea P – VERY GOOD Mad Anthony – The Stourbridge Lion Rpm 45 Mad River – Orange Fire EP – USA 7″ 45 PS (numbered) – psych acid rock garage Make Your Own CD Lot ~ $1.99 Each ~ $5.24 Shipping Any Order Size ~ Country Rock 1994 Mad Lion: Take It Easy/Big Box of Blunts 12 Vinyl Record – Weeded Records Clutch – Mad Sidewinder / Outland Special Clearance Vinyl Single RSD Ltd /5000 DANCE CRAZE Specials Madness Selecter 2 TONE Original ’81 UK Ska LP w/poster 1994 Fleer Flair Marvel Annual Trading Cards 1-150 * You-Pick* Complete your set The Center Cannot Hold: My Journey Through Madness – Paperback – GOOD MADNESS THE GET UP DVD AND CD SOUNDTRACK BRAND NEW AND SEALED CD # 2023 Topps Chrome Star Wars REFRACTORS & INSERTS pick a card finish your set Joe Cocker”Mad Dogs & Englishmen” Vinyl (EX) Obsession Methods Of Madness Black Vinyl LP Record New For GLOCK 26 27 33 39 GEN 1 2 3 4 5 Stainless Steel Guide Rod Assembly G26 Camel – Moonmadness [New Vinyl LP] UK – Import Madness 45 The Sun and the Rain NEW unplayed Marvel’s Doctor Strange in the Multiverse of Madness – Original Soundtrack 2XL Tom Holkenborg – Furiosa: A Mad Max Saga (Original Soundtrack) [New Vinyl LP] Metal Meat by Mad Butcher (Record, 2022) Mad Dogs & Englishmen by Joe Cocker: Used Mad Men: Season 2 – DVD – GOOD HEXILES #2 (OF 6) (MR) (PRESALE 12/11/2024) Brain on Fire (10th Anniversary Edition): My Month of Madness Jerry & Reggie MAD MIKE ROCKER 45RPM Shoo Shoo / Dream Baby PROMO – MOC 656 -EX+ Kung Fu Vampire Dead Sexy Cd Autographed By Savzilla & Kung Fu Vampire Mens Pullover Fleece Hoodie
